M:CNC stepperit

Matsushita 17PM-J142 - 42x42x40mm
- 6 wires
- 1.8°-step
- 24V
- 1.4A
- 2.3Ohm
- 250mNm - holding troque
- 3.1mH - inductance
- 44g*cm2 - rotor inertia
- 300g mass
- 8.3mNm torque




Määrä 2 kpl
Hinta:
- 10e / 1 kpl   + 5e posti (jos haluaa toimitus)
- 15e / 2kpl    + 8e posti  (jos haluaa toimitus)

~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

Shinano stp 42 - 42*42*40mm
- 6 wires
- 1.8° - step
- 12-36V
- 1.2A
- 4.6Ohm
- 373mNm holding torque




Määrä 1 kpl
Hinta:
- 10e / 1 kpl   + 5e posti (jos haluaa toimitus)

~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

Shinano stp 43 - 42*42*40mm
- 6 wires
- 1.8° - step
- 12-36V
- 1.2A - 1.4A
- 3.0Ohm
- 300mNm holding torque



Määrä 3 kpl
Hinta:
- 10e / 1 kpl   + 5e posti (jos haluaa toimitus)
- 25e / 3kpl    + 10e posti  (jos haluaa toimitus)

~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

Epson prrinter
- 4 wire



Määrä 2 kpl
Hinta:
- 8e / 1 kpl   + 5e posti (jos haluaa toimitus)
- 10e / 2kpl    + 8e posti  (jos haluaa toimitus)

~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

TEAC / matsushita
- 6 wire



Määrä 1 kpl
Hinta:
- 8e / 1 kpl   + 5e posti (jos haluaa toimitus)




Kaikki moottorit yhdessä  : hinta 70e ( posti maksa sisään)

Minun suomalainen on huono. Jos halua kysyä on Suomeksi - email tai sms , muuten voi soitaa on Englantiksi


044 351 0 454 - kovachev.svetoslav *at* gmail *.* com



Katso koko ilmoitus

Hi,

Because of update of my project i wish to offer some parts for sale:
-----------------------------------------------------------------------------------------
6 pcs of SHF25 - Linear Rod Rail Shaft Support - 

new, never used - price: 25e without delivery
===================================================
3pcs of  5 to 10mm  CNC Flexible  motor shaft coupler (new)

new, never used - price: 8e without delivery SOLD
===================================================

from that machine:

for sale is:

4pcs of  5 to 6mm  CNC Flexible  motor shaft coupler (only one is new, the other 3 are still on machine)

new&used - price: 12e without delivery

3 x stepper , nema 17
~~~~~~~~~~~~~~~~
Type:Stepper Nema 17    
Angle step:1.8°    
Voltage: 3.4V    
Rate current:1.7A
Phase resistance: 2 oM     
Phase inductance: 3 mH    
Holding torque: 4000 g.sm    
Lead wires: 4    
Rotor inertia: 54 g.cm2    
Detent torque: 220 g.cm    
Motor weight: 0.3 kg
Motor lenght: 40mm
Motor width: 42mm

used - price: 50e without delivery


CNC to PC breakboard - 5axis, limits, joystick control and more. Including CD with documents and LPT cable(mini USB not included)

never used - price: 14e SOLD

Controller board:


My design, prepared to carry 3 x A4983 Stepper Motor Driver Carrier with Voltage Regulators Pololu(http://www.pololu.com/catalog/product/1202/resources) - MAX 2A per phase 1:1 to 1:128 step , adjusted via jumper configuration. Input STEP,DIR,ENABLE from break board.
!!! That 3 A4983 controllers from the picture are NOT included, only the board !!!
that is the second one and it never been used, but tested and work perfect - price: 22e without delivery


contact only on mail please: kovachev.svetoslav (at) gmail (*) com

Well that`s right.. just to see what will be with my project and then i can think about.


Jussi - i try to send him(ParturiA), P.M here but i can`t(restriction i guess). Also i try to send him mail and lets see. Thanks again

TeacDance - nice frame! but.. there is only frame and is projected for ball screw that i do not have. Well lets say i was in negotiation with one ebay seller and for 3pcs , size what i need nut+lead screw price was 210$ including delivery.. Until now for sliding blocks and shafts already pay 240e and that will go too much, because if i continue with good motors, ball screws and ball bearing slides.. then will be good idea just to produce nice aluminium frame and to have good router.. but then the price will go close to.. that that i can buy ready  :-\ Thanks for the offer by the way


evvk - that was quite good tip! Thank you a lot and i need to apologize for my  paska suomen kieli  :( Just today i contact one of the guys(quite stupid on the website to be only phone numbers) and now wait their response with price tag.

Jussik - also quite good info! I`ll contact him now and lets see what will be.

Thank you guys.. real help  ;)

Hyvää uutavuotta  2013 ;)

porepe - I add all DXF files to my website http://longgo.eu/DXF/ but from all of them let's start with 9mm.dxf,15mm.dxf and 23mm MDF table. I have already the material and that MDF table is prepared to 550 x 800mm only holes will be nice to be machined(well to be the same space and horizontal). Can you ask your man what will cost that to me and see what will be. Thanks

pave - aserle.fi big company, they even do not return response to my mails.. For the employer... ha, you\re just right.. but for now the labor is not in situation to change bravely.  :-\

porepe - sound interesting, but why DXF? Well no problem at all, DXF,parasolid,... i use SW to make it and can produce any format. By the way even for that piece of crap that i have now is quite easy to use Vetric or CamBam based on DXF files  ;) Shall i add them to my website and he or you can download  them  or to send via mail?

Thanks  JuKa ;) - that image was in the beginning.Now.. look more like machine.  ;D BESTRON i ask maybe month ago, but they respond that not work wood(MDF/vaneri)

petteriu - i'll try to contact them, and lets see. Thanks.

Just out of curiosity - is that difficult to find company that work with private customers or only i'm the lucky one ..  :( Even few tools what i use, get order from UK.
Any tip will be bonus for me

Hi CNC gurus,
Hope i wont be killed if i write that topic in English(google translator will not help so much if i try to make it in Suomi).
I've made one small CNC-jursin , which was ok for few tests.. but it work far away from what i expect. Well do the job but i already plan proto 2: 

And here i come to the main question,and why i need help with some info - Where can i cut some parts with laser or water-jet machine?

Why i ask.. Well, the company where i work..have water-jet just my boss do not wish even to here to make something private because are few plates and i do not have company. And that was teh same answer what i get from most of the companies around - we do not cut wood or not work with private customers... huh..
Only one company made offer for.. 350e  ??? which is quite much i think.. but anyway, any idea where can i make my stuff in Rauma-Turku-Pori area...(or further with post delivery.. )

Thanks in advance